![]() Line up the holes you just drilled with the holes in the bracket and use screws to attach the bracket to the bumper. Now you are ready to mount the bracket to the bumper. These are just pilot holes so you don’t want to drill any deeper than 1/8 inch deep. Now, use a drill and a 1/8 inch drill bit to make shallow pilot holes in the bumper. If you are not using a bracket, draw marks where the plate’s holes are. Hold up the license plate bracket over this middle point and draw guide marks where the holes are. Find the middle of the height and mark that spot. First, measure your bumper with a measuring tape and mark the center with a pen or scotch tape. If your bumper is fiberglass, you’re good to get started. Drilling into metal is trickier so if you have never done it before, we recommend using the adhesive method instead. If your car does not have predrilled holes and you want to attach your license plate using screws, you can drills holes yourself.īefore you start you need to find out if you have a metal front bumper or one made out of fiberglass. Again, if you have a license plate frame, screw both this frame and the plate into the bracket at the same time. Now that the bracket is in place, you can attach the license plate to the bracket with a screwdriver. Turn this bolt clockwise with your fingers as far as it will go and then use a ratchet to tighten it fully. Next, push the bolt through the holes to attach the bracket plate to the tow hook stud. Insert the threaded end of the stud into the anchor slot. It is usually a small rectangle that you can press to pop the cover out (like a gas tank cover). Buy a tow hook license plate bracket kit that will come with everything you need.įirst, find the tow hook anchor and take off the plastic panel that covers it. Some cars have a tow hook anchor that you can use to install your license plate. ![]() ![]() If your plate comes with a frame, go ahead and push the screw through both the plate and frame before attaching to the bracket. Then, screw the license plate to the bracket using a screwdriver. Next, remove the protective film on the back of the bracket and place it onto the bumper. If it doesn’t line up with the bumper, it is the wrong kind of bracket. This is your final chance to make sure it is the right size for your car. Then, without peeling off the protective film, hold up the bracket in place to gauge how it will fit. Let the bumper air dry or wipe it dry with a microfiber cloth. For the adhesive to properly stick, the area needs to be clean. First, clean the front of your bumper with rubbing alcohol. Make sure to choose a bracket that will fit your car’s make and model. If you don’t want to drill into your bumper, you can buy an adhesive-mounted bracket. If you bought a used car without an owner’s manual, download a copy of your owner’s manual and print a copy to store in your glove box. If you worry about license plate theft, you can get security screws that are the same size.ĭon’t forget to put your vehicle’s registration receipt in your glove box together with the owner’s manual and insurance slip. Make sure the plate is secure but not overly tight. If your plate includes a frame, line the holes up with both the plate and the frame and then insert the screws. If your car has predrilled holes on the bumper, use these to line up your license plate and screw it in by turning the screw clockwise with a screwdriver. Play it safe and do this right to avoid a trip to the DMV. This could cause your old stickers to fall off with the new sticker attached. The bonding agent of previous stickers will begin to weaken over time. Stick the new stickers in the top corners of your license plate.ĭo not stick the new sticker on top of the old sticker. You may need to use the screwdriver to pry off the old stickers.Ĭlean the area with a clean cloth to ensure that the new stickers adhere well. Remove the old expiry tags if you are using your existing license plates. If your car has had license plates installed in the past, follow these simple steps. If Your Car Has Predrilled Holes on the Bumper The next steps will depend on if your car already had a license plate before and has predrilled holes or not. Want personalized license plates? Primo Registrations gives you the lowest price on custom plates. Check your glove compartment for this as well as the screws needed. You will need a flathead screwdriver, your new validation sticker, and the right screws.īrand new cars often come with license plate covers or license plate frames. ![]() Get Your Suppliesįirst, start by gathering the items necessary for this project. Save yourself a headache and learn how to install a license plate on your car in a few simple steps. While you may get off with a warning or a ticket, you could also have your car towed. You become a target for any police officer who sees you. Driving around without a license plate is illegal.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |